- 115 Volt AC, capacitor start electric motor.
- NEMA 5-15 grounded cord cap.
- Replacable fuse protection system.
- 8 inch inlet and outlet diameter.
- Damage resistant, cast aluminum blower housing
- Stamped steel fan.
- Rubber anti-vibration mounting.

- 115 Volt AC, capaitor start electric motor.
- NEMA 5-15P grounded cord cap.
- 8" diameter x 25' flexible ducts
- 12 gauge, spun steel blower housing construction.
- Lockable cover.
- Aluminum and composite fan construction.
- Rubber anti-vibration mounting.

- 12 Volt DC, permanent magnet motor.
- 50 ampere battery terminal connetions.
- 8 inch outlet diameter.
- 12 gauge, spun steel blower housing.
- Aluminum & composite fan construction.
- Rubber anti-vibration mounting.
- Ducting Available

- 12 Volt DC, permanent magnet motor.
- 50 ampere battery terminal connections.
- 8" diameter x 25' flexible duct and integral storage can.
- 12 gauge, spun steel blower housing construction.
- Rubber anti-vibration mounting.

- 115 Volts AC, capacitor start electric motor.
- NEMA 5-15P grounded cord cap.
- 12 inch inlet and outlet diameter.
- 12 gauge, steel blower housing construction.
- Aluminum and composite fan construction.
- Rubber anti-vibration mounting.

- 1400 watts, 115 VAC, 60 Hz, 12 amperes, single phase electric motor
- 3000 oscillations per minute
- Circuit Interruption Protection
- Slip Clutch
- 5" nominal width blades; Heat treated straight edge and scoring edge versions available

- Unitized welded steel frame.
- Special, alloy steel heat treated, cutting blade, 13.5 inch diameter, 5 inches maximum cutting depth.
- Win Oilite® type, sleeve type bearings, 25,000 lbs maximum down force capacity.
- Patented, twin screw, pivoting clamp conforms to variances in bucket shapes when mounting.
- Not for use with skid steer loaders.

-Diamond segment blades for use with the CS8 Series Random Crack Saw Products.
-Premium quality, dry cut type, for use with 1 inch diameter arbor shaft.
-8 inch nominal diameter x .250 inch cutting width, for normal use in fully cured concrete.

-Diamond segment blades for use with the CS8 Series Random Crack Saw Products.
-Premium quality, dry cut type, for use with 1 inch diameter arbor shaft.
-8 inch nominal diameter x .375 inch cutting width, for normal use in fully cured concrete.

-Diamond segment blades for use with the CS8 Series Random Crack Saw Products.
-Premium quality, dry cut type, for use with 1 inch diameter arbor shaft.
-8 inch nominal diameter x .250 inch cutting width, for normal use in asphalt and green type (abrasive)

- 13 HP Honda engine
- Max Driling Torque: 276 ft. lbs. at 2000 PSI
-144 RPM, no load
- 8 GPM System flow at 2000 PSI
- Holds 5 Gallons regular gasoline.
- Quick attach towbar complete with SAE Class II coupler
- 440 lbs

- Honda 11 HP gasoline engine
- Oil alert
- Dual element air cleaner and conversion for use with Propane.
- Complete with 20 lbs. industrial type Propane tank, hose, coupler and accessory kit.

- 3 HP 220 VAC, 50 Hz electric motor,
- Motor switch control
- Cord cap/plug assembly.

Digging Depth:15"

Flighting OD:36"
Cutting Dia.:37.5"
Digging Depth:3'

- 100 ft., CSA® rated, extra hard usage type 10-3 AWG cable, complete with Appleton ECCL203 or equivalent receptacle rated for hazardous location use on one end.
- To meet the hazardous location specification, this receptacle must be utilized with Appleton NCP2023 or equivalent cord cap only. The other end of the extension cord features capped wire terminals to allow for various wiring options. The extension cord can be "soft" wired according to National Electric Code® specifications.

-For field repairs of the SCF815 and SCFD825 statically conductive ducts only.
-Includes statically conductive patching material, statically conductive adhesive and instructions.
-Adhesive classified as hazardous material for shipping considerations.

- Equipped with Honda GX340 Series 11 HP gasoline engine with oil alert and Cyclone® type air filter.
- Vacuum Port: 3 inch, dry cutting and dual water feed system port for wet cutting applications
- Drive System: Dual B Series, V-belt/pulley and spur

Gast 16 Series pneumatic motor
- ON/OFF valve, regulator, filter unit, oiler unit, pressure gauge, muffler, hose lanyards, hose connecting fitting and anti-whip hose cable assemblies.
- Weight: 275 lbs

Equipped with full length auger flighting and straight, "E" series
- Bolt-on type earth blades.
- Flighting OD:2-1/4"
- Cutting Dia:2.5"
- Digging Depth:30"
- Drive (" round):1"
- Weight (lbs):8

Equipped with full length auger flighting and straight, "E" series
Bolt-on type earth blades.
Flighting OD:4"
Cutting Dia:5.2"
Digging Depth:30"
Drive (" round):1"
Weight (lbs):12

Equipped with full length auger flighting and straight, "E" series
Bolt-on type earth blades.
Flighting OD:8"
Cutting Dia:9.5"
Digging Depth:30"
Drive (" round):1"
Weight (lbs):20

-For use with 671 Dig-R-Tach®
-Available in 4 and 5 foot effective digging depths.
-Each equipped with 3/8 inch thickness, single pitch sectional or helicoid flighting the full length of the auger axle, Pengo® LDOBH type cast steel boring head and 2 inch hexagon drive connection.
-For use with Series 671 DIG-R-TACH and competitive models of popular hydraulically powered earth drilling attachments utilizing a 2 inch hexagon drive connection.
-Flighting OD:12" Cutting
-Dia.:13.5"
-Digging Depth:4'

For use with 671 Dig-R-Tach®
-Available in 4 and 5 foot effective digging depths.
-Each equipped with 3/8 inch thickness, single pitch sectional or helicoid flighting the full length of the auger axle, Pengo® LDOBH type cast steel boring head and 2 inch hexagon drive connection.
-For use with Series 671 DIG-R-TACH and competitive models of popular hydraulically powered earth drilling attachments utilizing a 2 inch hexagon drive connection.
-Flighting OD:16"
-Cutting Dia.:17.5"
-Digging Depth:4'

For use with 671 Dig-R-Tach®
-Available in 4 and 5 foot effective digging depths.
-Each equipped with 3/8 inch thickness, single pitch sectional or helicoid flighting the full length of the auger axle, Pengo® LDOBH type cast steel boring head and 2 inch hexagon drive connection.
-For use with Series 671 DIG-R-TACH and competitive models of popular hydraulically powered earth drilling attachments utilizing a 2 inch hexagon drive connection.
-Flighting OD:18"
-Cutting Dia.:19.5"
-Digging Depth:4'

For use with 671 Dig-R-Tach®
-Available in 4 and 5 foot effective digging depths.
-Each equipped with 3/8 inch thickness, single pitch sectional or helicoid flighting the full length of the auger axle, Pengo® LDOBH type cast steel boring head and 2 inch hexagon drive connection.
-For use with Series 671 DIG-R-TACH and competitive models of popular hydraulically powered earth drilling attachments utilizing a 2 inch hexagon drive connection.
-Flighting OD:24"
-Cutting Dia.:25.5"
-Digging Depth:4'

For use with 671 Dig-R-Tach®
-Available in 4 and 5 foot effective digging depths.
-Each equipped with 3/8 inch thickness, single pitch sectional or helicoid flighting the full length of the auger axle, Pengo® LDOBH type cast steel boring head and 2 inch hexagon drive connection.
-For use with Series 671 DIG-R-TACH and competitive models of popular hydraulically powered earth drilling attachments utilizing a 2 inch hexagon drive connection.
-Flighting OD:30"
-Cutting Dia.:31.5"
-Digging Depth:4'

For use with 671 Dig-R-Tach®
-Available in 4 and 5 foot effective digging depths.
-Each equipped with 3/8 inch thickness, single pitch sectional or helicoid flighting the full length of the auger axle, Pengo® LDOBH type cast steel boring head and 2 inch hexagon drive connection.
-For use with Series 671 DIG-R-TACH and competitive models of popular hydraulically powered earth drilling attachments utilizing a 2 inch hexagon drive connection.
-Flighting OD:36"
-Cutting Dia.:37.5"
-Digging Depth:4'

For use with 671 Dig-R-Tach®
-Available in 4 and 5 foot effective digging depths.
-Each equipped with 3/8 inch thickness, single pitch sectional or helicoid flighting the full length of the auger axle, Pengo® LDOBH type cast steel boring head and 2 inch hexagon drive connection.
-For use with Series 671 DIG-R-TACH and competitive models of popular hydraulically powered earth drilling attachments utilizing a 2 inch hexagon drive connection.
-Flighting OD:6"
-Cutting Dia.:7.5"
-Digging Depth:4'

For use with 671 Dig-R-Tach®
-Available in 4 and 5 foot effective digging depths.
-Each equipped with 3/8 inch thickness, single pitch sectional or helicoid flighting the full length of the auger axle, Pengo® LDOBH type cast steel boring head and 2 inch hexagon drive connection.
-For use with Series 671 DIG-R-TACH and competitive models of popular hydraulically powered earth drilling attachments utilizing a 2 inch hexagon drive connection.
-Flighting OD:8"
-Cutting Dia.:9.5"
-Digging Depth:4'

For use with 753 Dig-R-Tach®
-Available in 4 and 5 foot effective digging depths.
-Each equipped with 3/8 inch thickness, single pitch sectional or helicoid flighting the full length of the auger axle, Pengo® LDOBH type cast steel boring head and 2-9/16 inch round drive connection.
-For use with Series 753 DIG-R-TACH and competitive models of popular brands hydraulically powered earth drilling attachments utilizing a 2-9/16 inch round drive connection.
-Flighting OD:16"
-Cutting Dia.:17.5"
-Digging Depth:4'

For use with 753 Dig-R-Tach®
- Available in 4 and 5 foot effective digging depths.
- Each equipped with 3/8 inch thickness, single pitch sectional or helicoid flighting the full length of the auger axle, Pengo® LDOBH type cast steel boring head and 2-9/16 inch round drive connection.
- For use with Series 753 DIG-R-TACH and competitive models of popular brands hydraulically powered earth drilling attachments utilizing a 2-9/16 inch round drive connection.
- Flighting OD:12"
- Cutting Dia.:13.5"
- Digging Depth:5'

For use with 753 Dig-R-Tach®
-Available in 4 and 5 foot effective digging depths.
-Each equipped with 3/8 inch thickness, single pitch sectional or helicoid flighting the full length of the auger axle, Pengo® LDOBH type cast steel boring head and 2-9/16 inch round drive connection.
-For use with Series 753 DIG-R-TACH and competitive models of popular brands hydraulically powered earth drilling attachments utilizing a 2-9/16 inch round drive connection.
-Flighting OD:18"
-Cutting Dia.:19.5"
-Digging Depth:4'

For use with 753 Dig-R-Tach®
-Available in 4 and 5 foot effective digging depths.
-Each equipped with 3/8 inch thickness, single pitch sectional or helicoid flighting the full length of the auger axle, Pengo® LDOBH type cast steel boring head and 2-9/16 inch round drive connection.
-For use with Series 753 DIG-R-TACH and competitive models of popular brands hydraulically powered earth drilling attachments utilizing a 2-9/16 inch round drive connection.
-Flighting OD:24"
-Cutting Dia.:25.5"
-Digging Depth:4'

For use with 753 Dig-R-Tach®
-Available in 4 and 5 foot effective digging depths.
-Each equipped with 3/8 inch thickness, single pitch sectional or helicoid flighting the full length of the auger axle, Pengo® LDOBH type cast steel boring head and 2-9/16 inch round drive connection.
-For use with Series 753 DIG-R-TACH and competitive models of popular brands hydraulically powered earth drilling attachments utilizing a 2-9/16 inch round drive connection.
-Flighting OD:30"
-Cutting Dia.:31.5"
-Digging Depth:4'

For use with 753 Dig-R-Tach®
-Available in 4 and 5 foot effective digging depths.
-Each equipped with 3/8 inch thickness, single pitch sectional or helicoid flighting the full length of the auger axle, Pengo® LDOBH type cast steel boring head and 2-9/16 inch round drive connection.
-For use with Series 753 DIG-R-TACH and competitive models of popular brands hydraulically powered earth drilling attachments utilizing a 2-9/16 inch round drive connection.
-Flighting OD:36"
-Cutting Dia.:37.5"
-Digging Depth:4'

For use with 753 Dig-R-Tach®
-Available in 4 and 5 foot effective digging depths.
-Each equipped with 3/8 inch thickness, single pitch sectional or helicoid flighting the full length of the auger axle, Pengo® LDOBH type cast steel boring head and 2-9/16 inch round drive connection.
-For use with Series 753 DIG-R-TACH and competitive models of popular brands hydraulically powered earth drilling attachments utilizing a 2-9/16 inch round drive connection.
-Flighting OD:6"
-Cutting Dia.:7.5"
-Digging Depth:4'

For use with 753 Dig-R-Tach®
-Available in 4 and 5 foot effective digging depths.
-Each equipped with 3/8 inch thickness, single pitch sectional or helicoid flighting the full length of the auger axle, Pengo® LDOBH type cast steel boring head and 2-9/16 inch round drive connection.
-For use with Series 753 DIG-R-TACH and competitive models of popular brands hydraulically powered earth drilling attachments utilizing a 2-9/16 inch round drive connection.
-Flighting OD:8"
-Cutting Dia.:9.5"
-Digging Depth:4'

General 4750 Series Earth Auger GEN-4750-12E3
2-9/16" Round Auger Connection

General 4750 Series Earth Auger
4750-18E3
2-9/16" Round Auger Connection

General 4750 Series Earth Auger
2-9/16" Round Auger Connection

General 4750 Series Earth Auger
2-9/16" Round Auger Connection

Dia.: 7.5"
Length: 48"

Flighting OD:16"
Cutting Dia.:17.5"
Digging Depth:3'

Flighting OD:24"
Cutting Dia.:25.5"
Digging Depth:3'

Flighting OD:8"
Cutting Dia.:9.5"
Digging Depth:3'

Flighting OD:30"
Cutting Dia.:31.5"
Digging Depth:3'

For use with all skid loaders.
Utilizing the bobcat type bucket attachment system.

-Equipped with 1.5 HP, 3450 RPM.
-115/230 VAC, 60 HZ, Totally Enclosed Air Over (TEAO) electric motor.
-Factory wired to operate on 115 VAC.
-Can be field wired to operate on 230 VAC

- Floor Covering Stripper
- 16 inch maximum cutting width
- Single phase, 115/230 VAC, 60 Hz
- Horse Power: 3/4HP (.56kw)
- Includes: FCS16-110 4" x 6" straight blade; FCS16-1300 3" x 10" straight blade
- 37 foot cord

- For SCFD825 collapsible duct.
- Heavy duty, welded, aluminum construction with full, protective cover and carry handle.
- Bright enamel finish.

-24 inch nominal diameter, 6 mil thickness, clear polyethylene material.
-Can be attached to the EP17 and the GP21 Positive Pressure Ventilators for pressure type ventilation applications.
-Bend radius when inflated can be restricted.
-Disposable by acceptable methods or can be reused.

- 8 in. diameter x 25 ft. length.
- Wire helix reinforced with anti-scuff strip.
- Complete with aluminum attachment cuff and static ground leads.
- For use with the Model EP8HL Blower only.

- Equipped with 5 HP 220/230 VAC
- 50 HZ electric motor and cord
- Weight: 160 lbs

- Equipped with Honda GX160 Series 5.5 HP gasoline engine
- Oil alert
- Cyclone type air cleaner
- Weight: 160 lbs

- Equipped with Honda GX340 Series 11 HP gasoline engine with oil alert, Cyclone® type air cleaner and conversion for use with Propane.
- Complete with 14 lbs cylinder, hose and accessory kit.